CONVOW Robotic Vacuum Cleaner Wheel Assembly Instruction Manual

1. Inleiding

This manual provides detailed instructions for the installation, operation, and maintenance of your CONVOW Robotic Vacuum Cleaner Wheel Assembly. This replacement part is designed for specific Proscenic robotic vacuum cleaner models to ensure optimal performance and mobility.

2. Product voorbijview

2.1 Componenten

The CONVOW Wheel Assembly includes the motor, wheel, and necessary wiring for integration into your robotic vacuum cleaner.

2.2 Compatibiliteit

This wheel assembly is compatible with the following Proscenic robotic vacuum cleaner models:

• Proscenic 820
• Proscenic 820S
• Proscenic 820T
• Proscenic 830
• Proscenic 830T
• Proscenic 850T

Image 1: A CONVOW robotic vacuum cleaner left wheel assembly, viewed from an angle, showing the wheel, housing, and connected wires. This image illustrates the complete unit.

3. Installatie-instructies

3.1 Benodigde hulpmiddelen

• Kleine kruiskopschroevendraaier
• Pry tool (optional, for gentle removal of covers)

3.2 Werkwijze

1. Power off and unplug your robotic vacuum cleaner.
2. Place the vacuum cleaner upside down on a clean, flat surface.
3. Locate the screws securing the bottom cover of the vacuum cleaner. Remove these screws and carefully detach the bottom cover.
4. Identify the existing wheel assembly that needs replacement. It will be secured by screws and connected by a wire harness.
5. Carefully disconnect the wire harness from the main board or connector. Note the orientation for reinstallation.
6. Remove the screws holding the old wheel assembly in place.
7. Gently lift out the old wheel assembly.
8. Position the new CONVOW Wheel Assembly into the vacant slot. Ensure it aligns correctly with the mounting points.
9. Secure the new wheel assembly with the screws previously removed. Do not overtighten.
10. Reconnect the wire harness to its corresponding connector. Ensure a secure connection.
11. Replace the bottom cover and secure it with its screws.
12. Flip the vacuum cleaner upright and test its operation.

Image 2: Two CONVOW robotic vacuum cleaner wheel assemblies viewed from the underside, revealing the motor and circuit board components. This view is typical during the replacement process.

Image 3: Two CONVOW robotic vacuum cleaner wheel assemblies, showing the top housing with 'L' and 'R' markings for Left and Right. These markings assist in correct orientation during installation.

4. Bediening

4.1 Controle na installatie

After installation, power on your robotic vacuum cleaner. Observe its movement. The new wheel assembly should allow for smooth navigation and obstacle traversal. If the vacuum cleaner exhibits unusual movement or error codes, refer to the Troubleshooting section.

5. Onderhoud

5.1 Reinigen

Periodically inspect the wheel assembly for tangled hair, dust, or debris. Use a small brush or cloth to clean the wheels and surrounding areas. Ensure the wheel rotates freely.

5.2 Inspectie

Check for any signs of wear or damage to the wheel tread or housing. Timely replacement of worn parts ensures consistent cleaning performance.

6. Probleemoplossing

6.1 Wheel Not Moving or Sticking

• Check for obstructions: Remove any hair, string, or debris tangled around the wheel axle.
• Re-seat the wheel assembly: Ensure the assembly is properly seated and all screws are tightened.
• Check wire connection: Verify the wire harness is securely connected.

6.2 Vacuum Cleaner Moving Unevenly

• Inspect both wheel assemblies: Ensure both left and right wheels are clean and functioning correctly.
• Verify correct wheel installation: Confirm that the left wheel is installed on the left side and the right wheel on the right side (if applicable, based on markings).

7. Specificaties

7.1 Productdetails

• Merk: CONVOW
• Compatibele modellen: Proscenic 820, 820S, 820T, 830, 830T, 850T
• Onderdeeltype: Robotic Vacuum Cleaner Wheel Assembly
• Materiaal: High-quality, wear-resistant materials
• Artikelgewicht: 0.035 ounce (ongeveer 1 gram)
• ASIN: B0CHXPYCSJ
• Fabrikant: caochunxiu

8. Garantie en ondersteuning

8.1 Productondersteuning

For further assistance, questions regarding installation, or to report any issues, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact information.

8.2 Garantie-informatie

Please refer to the warranty information provided at the time of purchase or contact the seller for details regarding the warranty period and terms for this replacement part.