BDCOM S2900-24T4X-2AC Ethernet Layer-3 Lite Switch Gebruikershandleiding

1. Inleiding

This manual provides essential information for the installation, operation, and maintenance of the BDCOM S2900-24T4X-2AC Ethernet Layer-3 Lite Switch. Please read this manual thoroughly before using the device to ensure proper setup and functionality. Retain this document for future reference.

2. Product voorbijview

The BDCOM S2900-24T4X-2AC is a high-performance Ethernet Layer-3 Lite switch designed for various networking environments. It features 24 Gigabit Ethernet (GE) TX ports and 4 10 Gigabit Ethernet (10GE) SFP+ ports, providing flexible connectivity options. The switch also includes a console port for management and supports standard 19-inch rack-mounted installation.

2.1 Belangrijkste kenmerken

• 1 Console port for device management.
• 24 Gigabit Ethernet (GE) TX ports for high-speed network connections.
• 4 10 Gigabit Ethernet (10GE/GE) SFP+ ports for uplink or high-bandwidth connections.
• AC 110V ~ 220V input, 60 Hz power supply.
• Ventilatorloos ontwerp voor een stille werking.
• 1U height, suitable for standard 19-inch rack-mounted installation.

2.2 Indeling van het voorpaneel

Figure 1: Front Panel Diagram of BDCOM S2900-24T4X-2AC Switch, highlighting 24 Gigabit RJ45 ports, 4 10G/1G SFP+ ports, and the Console port.

• Console-poort: RJ45-poort voor toegang tot de opdrachtregelinterface (CLI).
• GE TX Ports (1-24): 24 Gigabit Ethernet ports for connecting network devices.
• 10GE/GE SFP+ Ports (TE1-TE4): 4 SFP+ slots supporting 10 Gigabit or 1 Gigabit fiber optic transceivers.
• LED-indicatoren: System (SYS), Power (PWR), and individual port status indicators.

Figuur 2: Gedetailleerde voorkant view of the BDCOM S2900-24T4X-2AC switch, showing the arrangement of ports and indicators.

2.3 Indeling achterpaneel

Afbeelding 3: Achter view of the BDCOM S2900-24T4X-2AC switch, displaying the AC power input and power switch.

• Wisselstroom ingang: Connector for the AC power cord (100-240 VAC, 50/60 Hz).
• Aan / uit schakelaar: On/Off switch for the device.

3. Installatie

Follow these steps for proper installation of your BDCOM S2900-24T4X-2AC switch.

3.1 Voorbereiding van de locatie

• Zorg ervoor dat de installatielocatie schoon, droog en goed geventileerd is.
• Houd de omgevingstemperatuur tussen 0°C en 50°C (32°F en 122°F).
• Avoid direct sunlight, heat sources, and excessive dust.
• Ensure adequate space around the switch for proper airflow, especially at the sides where ventilation is located.

3.2 Rekmontage

The switch is designed for standard 19-inch rack-mounted installation (1U height).

1. Bevestig de meegeleverde rackmontagebeugels aan de zijkanten van de switch met behulp van de bijgeleverde schroeven.
2. Align the switch with the rack posts and secure it using appropriate rack screws.
3. Ensure the switch is level and securely fastened in the rack.

3.3 Stroomaansluiting

1. Zorg ervoor dat de aan/uit-schakelaar op het achterpaneel in de UIT-stand staat.
2. Connect one end of the AC power cord to the power input on the rear panel of the switch.
3. Connect the other end of the AC power cord to a grounded power outlet (100-240 VAC, 50/60 Hz).
4. Flip the power switch to the ON position. The Power (PWR) LED on the front panel should illuminate.

3.4 Netwerkverbindingen

• GE TX Ports: Connect standard RJ45 Ethernet cables from your network devices (servers, workstations, other switches) to the GE TX ports (1-24).
• 10GE/GE SFP+ Ports: Insert compatible SFP+ transceivers into the SFP+ slots (TE1-TE4). Connect fiber optic cables from other network devices or uplinks to these transceivers. Ensure the transceivers and cables match the required speed (1G or 10G).
• Console-poort: For initial configuration and management, connect a console cable (RJ45 to DB9 or USB) from your management workstation to the console port.

4. Initiële configuratie

The BDCOM S2900-24T4X-2AC switch can be configured via its Command Line Interface (CLI) through the console port or via a web-gebaseerde grafische gebruikersinterface (GUI).

4.1 Console Access (CLI)

1. Connect your computer to the switch's console port using a console cable.
2. Open een terminalemulatieprogramma (bijvoorbeeld PuTTY, Tera Term) op uw computer.
3. Configure the serial port settings:
   • Baudsnelheid: 9600
   • Gegevensbits: 8
   • Pariteit: Geen
   • Stop bits: 1
   • Stroomregeling: Geen
4. Power on the switch. The boot-up messages will appear in the terminal window.
5. Log in using the default credentials (refer to the official BDCOM documentation for default username and password).
6. Begin configuring the switch according to your network requirements. The command structure is similar to Cisco IOS.

4.2 Web-based Management (GUI)

Once the switch has an IP address configured (either manually via CLI or via DHCP), you can access its web interface.

1. Ensure your management computer is on the same network segment as the switch.
2. Open een web browser en voer het IP-adres van de switch in.
3. Log in met de juiste inloggegevens.
4. The GUI provides a user-friendly interface for configuring various switch functions. Note that the included PKI certificate may be expired, requiring generation of a new one for secure access.

For detailed command references and advanced configuration, please consult the official BDCOM S2900 series documentation.

5. Gebruiksaanwijzing

The BDCOM S2900-24T4X-2AC switch operates automatically once configured. Here are general operational guidelines:

• Aan/uit: Use the power switch on the rear panel. Always ensure proper shutdown procedures if available through CLI/GUI before powering off.
• LED-indicatoren: Controleer de LED's op het voorpaneel voor de operationele status:
  • PWR (vermogen): Continu groen geeft aan dat de schakelaar is ingeschakeld.
  • SYS (Systeem): Indicates system status (e.g., solid green for normal operation, blinking for activity or errors). Refer to the full manual for specific patterns.
  • Poort-LED's: Indicate link status and activity for each GE and SFP+ port.
• Netwerkconnectiviteit: Ensure all connected devices are properly cabled and configured for network access.
• Layer-3 Lite Functionality: The switch supports basic Layer-3 routing capabilities. Configure VLANs, IP interfaces, and static routes as needed for inter-VLAN routing and network segmentation.
• Linkaggregatie (LACP): For increased bandwidth and redundancy, configure Link Aggregation Control Protocol (LACP) on multiple ports to form a single logical link (port channel). Ensure a lower value for the 'agg-period' parameter if configuring LACP.

6. Onderhoud

Regelmatig onderhoud zorgt ervoor dat uw switch lang meegaat en optimaal presteert.

• Schoonmaak: Reinig de buitenkant van de schakelaar regelmatig met een zachte, droge doek. Gebruik geen vloeibare reinigingsmiddelen of spuitbussen. Zorg ervoor dat de ventilatieopeningen vrij zijn van stof en andere obstakels.
• Firmware-updates: Check the BDCOM official website for the latest firmware updates. Applying updates can improve performance, add features, and fix bugs. Follow the provided instructions carefully during firmware upgrades.
• Configuratieback-up: Regularly back up your switch configuration to an external storage device. This allows for quick restoration in case of a device reset or failure.
• Milieumonitoring: Zorg ervoor dat de werkomgeving binnen de gespecificeerde temperatuur- en vochtigheidsbereiken blijft.

7. Probleemoplossing

This section provides solutions to common issues. For more complex problems, contact technical support.

7.1 Stroomproblemen

• Geen stroom:
  • Controleer of het netsnoer goed is aangesloten op zowel de schakelaar als het stopcontact.
  • Zorg ervoor dat de aan/uit-schakelaar op het achterpaneel in de stand AAN staat.
  • Controleer het stopcontact met een ander apparaat om te bevestigen dat het werkt.

7.2 Problemen met netwerkconnectiviteit

• Geen link op een poort:
  • Check the Ethernet or fiber cable connection. Ensure it is securely plugged into both the switch port and the connected device.
  • Verify the cable is not damaged. Try a different cable.
  • Controleer of het aangesloten apparaat is ingeschakeld en correct functioneert.
  • Check the port status LEDs on the switch. If the LED is off, there might be no link.
  • For SFP+ ports, ensure the transceiver is correctly seated and compatible. The switch can be particular about transceivers.
• Trage netwerkprestaties:
  • Check for network congestion.
  • Verify duplex and speed settings on the switch port and connected device.
  • Ensure cables are appropriate for the speed (e.g., Cat5e/6 for Gigabit Ethernet).

7.3 Management Access Issues

• Cannot Access CLI via Console:
  • Verify the console cable connection.
  • Check the serial port settings in your terminal emulation program (Baud Rate, Data Bits, Parity, Stop Bits, Flow Control).
  • Zorg ervoor dat de juiste COM-poort is geselecteerd.
• Cannot Access GUI via Web Browser:
  • Verify the switch has an IP address and your computer can reach it (ping the IP address).
  • Zorg ervoor dat uw web browser is not blocking the connection due to certificate warnings (the default certificate may be expired).
  • Wis de browsercache of probeer een andere browser.

8. Specificaties

9. Veiligheidsinformatie

Neem de volgende veiligheidsmaatregelen in acht om letsel en schade aan het apparaat te voorkomen:

• Always connect the power cord to a grounded electrical outlet.
• Gebruik het apparaat niet in natte of damp voorwaarden.
• Zorg voor goede ventilatie om oververhitting te voorkomen.
• Open het apparaat niet casing. Laat alle onderhoudswerkzaamheden over aan gekwalificeerd personeel.
• Plaats geen zware voorwerpen op de schakelaar.
• Schakel de stroom uit voordat u het apparaat schoonmaakt of verplaatst.

10. Garantie en ondersteuning

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official BDCOM website. You may also contact your reseller for assistance.

BDCOM Official Webwebsite: www.bdcom.com.cn