Leviton DOS05-1LZ Decora Motion Sensor Light Switch Instruction Manual

1. Inleiding

The Leviton DOS05-1LZ Decora Motion Sensor Light Switch is designed to provide automatic lighting control based on occupancy and motion detection. This 180° Passive Infrared (PIR) sensor can operate in either single-pole or 3-way configurations and does not require a neutral wire for installation, making it suitable for a wide range of residential applications. It is compatible with various load types including LED, CFL, Incandescent, Halogen, Magnetic Low Voltage, elektronische lage voltage, and motor loads up to ¼ HP. This device helps enhance convenience and energy efficiency by automatically turning lights on when motion is detected and off after a set period of inactivity.

The switch includes interchangeable faceplates in White, Ivory, and Light Almond to match your decor. It can also be used to comply with 2019 California Title 24, Part 6 Vacancy Control Device Requirements.

2. Veiligheidsinformatie

WARNING: To avoid fire, shock, or death, always turn off power at the circuit breaker or fuse and test to ensure power is off before wiring. If you are unsure about any part of these instructions or are not comfortable or familiar with electrical wiring, contact a licensed electrician.

• This device is designed for use with copper or copper-clad wire only.
• Do not mount near a heat source or in drafty areas of the home, as temperature changes can affect sensor performance.
• Avoid mounting in motion-heavy areas where unintended motion will be within the sensor's field of view, unless adjusted for specific coverage.

3. Inhoud van het pakket

• One Leviton DOS05-1LZ Motion Sensor Light Switch
• Interchangeable faceplates (White, Ivory, Light Almond)
• Installatie-instructies

4. Installatie

4.1. Benodigd gereedschap

• Platte schroevendraaier
• Kruiskopschroevendraaier
• Electrician's pliers
• Draadstripper
• Elektrische tape
• Handheld voltagde tester
• Properly sized wire connectors

4.2. Stappen vóór installatie

1. Schakel de stroom uit via de stroomonderbreker of zekering.
2. Remove the existing switch plate and unscrew the old device from the wall box.
3. Carefully pull the device out until you clearly see the wires.
4. Gebruik een voltage tester to ensure no power is present in the box.
5. Carefully disconnect all wiring from the old device and remove it.
6. Straighten and separate each wire. Ensure no exposed metal ends are touching.

4.3. Wiring the Motion Sensor Switch

The DOS05-1LZ can be wired with or without a neutral wire. Identify the wires in your wall box to determine the appropriate wiring configuration.

Figure 1: Leviton DOS05-1LZ Motion Sensor Switch with pre-stripped wires.

Afbeelding 2: Terug view of the switch showing wiring terminals and labels.

4.3.1. Wiring without a Neutral Wire (Ground Connection)

• Twist the green and yellow ground lead wire from the device and the green sleeve ground wire (if present) to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
• For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.

4.3.2. Wiring with a Neutral Wire

• Remove the green sleeve from the white wire on the product. Connect this white wire to the white neutral wire(s) in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the green and yellow ground lead wire from the device to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
• Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
• For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.

4.4. Laatste stappen

1. Gently bend the wires and push them into the wall box.
2. Screw the sensor into the wall box.
3. Install the wall plate (sold separately).
4. Herstel de stroom bij de stroomonderbreker of zekering.

5. Gebruiksaanwijzing

5.1. Basisbediening

• Automatisch aan/uit: After a warm-up period (10-20 seconds), the lights will automatically turn on with the first motion detected. They will turn off after a set period of inactivity.
• Handmatig aan/uit: Press the lower part of the push pad to manually turn the lights on or off.
• Motion Detected Indicator: The red indicator light will flash anytime motion is detected.
• Light Off Indicator: The green indicator light illuminates when the light (load) it controls is off.

5.2. Programmeerbare instellingen

The DOS05-1LZ offers three programmable settings: Timer, Sensitivity, and Ambient Light. These settings can be adjusted directly from the push pad without tools or removing the faceplate.

Figure 3: Adjust settings by pressing the push pad, no tools required.

5.2.1. Programmeermodus invoeren

1. Manually turn the light ON by pressing the push pad. The green LED will be off.
2. Press the TOP and BOTTOM of the push pad simultaneously for 5 seconds.
3. The green LED will turn on for 5 seconds, then the red LED will blink once, and the green LED will blink three times. This indicates you are in Programming Mode, currently in the Timer Setting (Option 3, 10 minutes, default).

Opmerking: Programming Mode will time out after 30 seconds if no activity is detected, and changes will not be saved.

5.2.2. Changing Settings and Options

• To change the Setting (Timer, Sensitivity, Ambient Light): Press the TOP of the push pad. The red LED will blink to indicate the setting number (1 blink for Timer, 2 for Sensitivity, 3 for Ambient Light).
• To change the Setting Option (e.g., 1 minute, 5 minutes for Timer): Press the BOTTOM of the push pad. The green LED will blink to indicate the option number (1 blink for Option 1, 2 for Option 2, etc.).

5.2.3. Timer Setting (Setting 1)

Adjusts the duration the light remains ON after motion was last detected.

• Option 1: 1 Minute
• Option 2: 5 Minutes
• Option 3: 10 Minutes (Default)
• Option 4: 20 Minutes

5.2.4. Sensitivity Setting (Setting 2)

Adjusts the device's sensitivity to motion, affecting the detection range.

• Option 1: Low (50% range)
• Option 2: Medium (Default)
• Option 3: High (Maximum coverage area)

Figure 4: 180° PIR detection range, up to 900 sq. ft. Customize sensing range/coverage area for your application.

5.2.5. Ambient Light Setting (Setting 3 - Occupancy Sensors Only)

Adjusts the device's sensitivity to natural light, preventing lights from turning on if there is ample natural light in the room.

• Option 1: Low Light Level
• Option 2: Medium Light Level (Default)
• Option 3: High/Brightest Light Level
• Option 4: Disabled (Light turns on for all light levels regardless of ambient light)

5.3. Temporary Modes

5.3.1. Testmodus

Turns on the light for 5 seconds every time motion is detected. Useful for testing field of view coverage after installation.

• In staat te stellen: Press and hold the TOP of the push pad for 5 seconds. The red light will blink once every 2 seconds.
• Verlaten: Press the TOP or BOTTOM of the push pad, or it will automatically time out after 2 minutes.

5.3.2. Temporary Bypass Mode (Occupancy Sensors Only)

Ignores motion, preventing detection and keeping the light or load off. Useful when you want a room to remain dark even if there is motion (e.g., watching a movie).

• Activeren: Press and hold the BOTTOM of the push pad for 5 seconds. The green light will double flash every 2 seconds.
• Verlaten: Press the TOP or BOTTOM of the push pad.

6. Probleemoplossing

7. Specificaties

• Modelnummer: DOS05-1LZ
• Werkingsmodus: AAN-UIT-AAN
• Huidige beoordeling: 2 Amps
• Bedrijfsvolumetage: 120 Volt
• Contactpersoon: Normaal geopend
• Aansluittype: Krimpen
• Terminal: Blad
• Artikelafmetingen (L x B x H): 1.38 x 1.73 x 4.13 inch
• Circuit Type: 3-weg
• Actuatortype: Drukknop
• Contactmateriaal: Fosforbrons
• Internationale beschermingsclassificatie: IP54
• Aantal posities: 1
• Lagere temperatuurclassificatie: 70 graden Fahrenheit
• Hogere temperatuurclassificatie: 100 graden Fahrenheit
• Type controller: Drukknop
• Controlemethode: Aanraken
• Connectiviteitsprotocol: X-10
• Kleur: White/Ivory/Light Almond
• Wattage: 600 watt
• Compatibele apparaten: LED, CFL, Incandescent, Halogen, Magnetic Low Voltage, elektronische lage voltage, Motor loads
• Energiebron: Elektrische kabel
• Artikelgewicht: 4.6 ons

8. Onderhoud

To maintain optimal performance and appearance of your Leviton Motion Sensor Light Switch, follow these simple guidelines:

• Schoonmaak: Gebruik een zachte, damp cloth to clean the surface of the switch. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
• Inspectie: Periodically inspect the switch for any signs of damage, loose connections, or unusual operation. If any issues are observed, turn off power at the circuit breaker and consult a qualified electrician.
• Lensverzorging: Keep the sensor lens clean and free from dust or obstructions to ensure accurate motion detection.
• Milieuoverwegingen: Ensure the switch is not exposed to excessive moisture or extreme temperatures beyond its operating range, as this can affect its lifespan and functionality.

9. Garantie en ondersteuning

This Leviton Motion Sensor Light Switch (DOS05-1LZ) comes with a 5 jaar beperkte garantie. For warranty claims, technical support, or further assistance, please contact Leviton customer service or visit their official webwebsite. Bewaar uw aankoopbewijs voor de garantievalidatie.