Novastar CVT4K-S Fiber Converter User Manual

1. Inleiding

The Novastar CVT4K-S is a fiber converter designed to facilitate signal conversion between optical fiber and twisted pair cables. This device enables stable and long-distance signal transmission, minimizing interference. Its user-friendly design simplifies connections for terminal devices and streamlines on-site installations.

2. Veiligheidsinformatie

• Zorg ervoor dat het apparaat is aangesloten op een geaard stopcontact.
• Stel het apparaat niet bloot aan vocht of extreme temperaturen.
• Vermijd het blokkeren van ventilatieopeningen om oververhitting te voorkomen.
• Only use the specified power supply.
• Laat alle onderhoudswerkzaamheden over aan gekwalificeerd personeel.
• Handle fiber optic cables with care; avoid bending them sharply.

3. Producteigenschappen

• Converts signals between optical fiber and twisted pair cables.
• Supports stable, long-distance signal transmission.
• Designed for ease of use and simplified on-site connections.
• Equipped with multiple Ethernet and fiber optic ports for versatile connectivity.

4. Apparaat voorbijview

The Novastar CVT4K-S features a robust rear panel with various input and output ports for signal and control. Understanding these connections is crucial for proper setup and operation.

Figuur 1: Rear panel of the Novastar CVT4K-S Fiber Converter. This image displays the 16 Ethernet output ports, the control Ethernet port, USB port, four optical fiber ports (OPT 1-4), and the dual AC power inputs with a power switch.

4.1 Poortidentificatie

• Ethernet Output Ports (1-16): These 16 RJ45 ports are used for outputting converted signals to display devices or other network equipment.
• Control Ethernet Port: An RJ45 port labeled 'CONTROL ETHERNET' for connecting to a control PC or network for device configuration and management.
• USB-poort: A USB Type-B port for direct connection to a computer for configuration or firmware updates.
• Optical Fiber Ports (OPT 1-4): Four SFP+ slots for fiber optic input. OPT 1 and OPT 2 are designated as 'MASTER' inputs, while OPT 3 and OPT 4 serve as 'BACKUP' inputs for redundancy.
• AC Power Inputs: Two AC 100-240V~50/60Hz power inputs. One is a standard IEC C14 inlet, and the other is a Neutrik powerCON compatible connector, providing redundant power options.
• Aan / uit schakelaar: Toggles the device power on or off.

5. Installatie-instructies

Follow these steps to set up your Novastar CVT4K-S Fiber Converter:

1. Stroomaansluiting: Connect the provided AC power cable to one of the AC power input ports on the rear panel and plug it into a suitable power outlet (AC 100-240V~50/60Hz). For redundancy, connect a second power cable to the other input.
2. Glasvezelingang: Insert the SFP+ modules (not included) into the desired optical fiber ports (OPT 1-4). Connect your fiber optic cables from the signal source to these SFP+ modules. Use OPT 1/2 for primary input and OPT 3/4 for backup if redundancy is required.
3. Ethernet-uitgang: Connect standard Ethernet cables from the 16 Ethernet output ports (1-16) to your receiving devices, such as LED display panels or other network equipment.
4. Besturingsaansluiting (optioneel): For device configuration and monitoring, connect an Ethernet cable from the 'CONTROL ETHERNET' port to your control PC or network switch. Alternatively, use a USB cable to connect the USB port directly to a PC.
5. Inschakelen: Flip the power switch to the 'ON' position. The device will power on, and indicator lights will illuminate.

6. Gebruiksaanwijzing

Once the Novastar CVT4K-S is set up, operating it involves ensuring proper signal flow and, if necessary, configuring settings via the control interface.

1. Signaalstroom: The CVT4K-S automatically converts the incoming optical fiber signal into Ethernet signals, which are then output through the 16 Ethernet ports. Ensure your signal source is active and transmitting data.
2. Indicatielampjes: Observe the indicator lights on the device. These typically indicate power status, signal presence, and data activity on the respective ports. Refer to the device's specific LED behavior for detailed status information.
3. Configuration (via Control Software): If advanced settings or monitoring are required, connect your control PC via the Ethernet or USB port. Use the official Novastar control software (available from Novastar's website) to access and adjust device parameters. This may include input/output mapping, redundancy settings, and status monitoring.
4. Ontslag: If using the backup optical fiber inputs (OPT 3/4), the device will automatically switch to the backup input if the primary (OPT 1/2) signal is lost, ensuring uninterrupted operation.

7. Onderhoud

Regular maintenance helps ensure the longevity and optimal performance of your CVT4K-S Fiber Converter.

• Schoonmaak: Periodically clean the exterior of the device with a soft, dry cloth. Do not use liquid cleaners or aerosols. Ensure ventilation openings are free from dust and debris.
• Kabelbeheer: Ensure all cables are securely connected and not under undue stress. Avoid sharp bends in fiber optic cables.
• Firmware-updates: Bekijk de officiële website van Novastar. website periodically for firmware updates. Applying updates can improve performance, add features, or resolve issues. Follow the provided instructions carefully during firmware updates.
• Opslag: When not in use, store the device in a cool, dry environment, away from direct sunlight and extreme temperatures.

8. Probleemoplossing

If you encounter issues with your CVT4K-S, refer to the following common troubleshooting steps:

• Geen stroom:
  • Controleer of de voedingskabel goed is aangesloten op zowel het apparaat als het stopcontact.
  • Zorg ervoor dat de aan/uit-schakelaar op 'AAN' staat.
  • Controleer of het stopcontact werkt door het te testen met een ander apparaat.
• Geen signaaluitvoer:
  • Confirm that the fiber optic input cables are correctly connected and the SFP+ modules are properly seated.
  • Check the signal source to ensure it is active and transmitting.
  • Verify that the Ethernet output cables are securely connected to the receiving devices.
  • Check the status indicator lights for the fiber and Ethernet ports; they should indicate activity.
• Instabiele verbinding:
  • Inspect all cables for damage or loose connections.
  • Ensure the SFP+ modules are compatible and functioning correctly.
  • Check for environmental interference or excessive cable lengths that might affect signal integrity.
• Control Software Not Connecting:
  • Ensure the control Ethernet or USB cable is properly connected.
  • Verify network settings on your PC if using an Ethernet connection (IP address, subnet mask).
  • Restart the control software and the CVT4K-S device.

9. Specificaties

10. Garantie en ondersteuning

For warranty information and technical support, please contact Novastar directly or refer to their official website. Keep your purchase receipt and product model number (P.A.EQA0.0-00001) handy when seeking support.

Novastar Official Webwebsite: www.novastar.tech