Tomzn TOVPD1-80-EC Adjustable Over/Under Voltage and Over Current Protection Device User Manual

1. Inleiding

This manual provides detailed instructions for the installation, operation, and maintenance of the Tomzn TOVPD1-80-EC Adjustable Over/Under Voltage and Over Current Protection Device. This device is designed to protect electrical appliances and circuits from damage caused by voltage fluctuations and excessive current. Please read this manual thoroughly before use to ensure safe and correct operation.

2. Veiligheidsinformatie

• De installatie moet worden uitgevoerd door een gekwalificeerde elektricien.
• Zorg ervoor dat de voeding is losgekoppeld vóór installatie of onderhoud.
• Do not operate the device in wet conditions or with wet hands.
• Verify that the device's specifications match your electrical system requirements.
• Houd kinderen uit de buurt van elektrische installaties.

3. Product voorbijview

3.1. Belangrijkste functies

• Overvoltage-bescherming
• Onder-voltage-bescherming
• Overstroombeveiliging
• Automatisch herstel
• Realtime voltagen weergeven
• Real-time current display
• Instelbaar volumetage calibration (±10%)
• Fabrieksresetfunctie
• Error inquiry function

3.2. Apparaatcomponenten

The device features a digital display for voltage and current, indicator lights for protection status, and control buttons for settings adjustment.

Figuur 1: Voorkant view of the Tomzn TOVPD1-80-EC protection device. Note: The image displays model TOVPD1-60-EC, but the instructions apply to the TOVPD1-80-EC model with an 80 Ampere beoordeling.

The device includes input terminals (IN) and output terminals (OUT) for electrical connections, along with a power indicator and status LEDs for over-voltage (>V), under-voltage (<V), and over-current (>A).

4. Installatie

The TOVPD1-80-EC device is designed for DIN rail mounting (35mm). Follow these steps for proper installation:

1. Stroomonderbreking: Before starting, ensure the main power supply to the circuit is completely disconnected to prevent electrical shock.
2. Montage: Snap the device onto a standard 35mm DIN rail in your electrical panel.
3. Bedrading:
   • Connect the incoming live (L) and neutral (N) wires from the power source to the "IN" terminals of the device.
   • Connect the outgoing live (L) and neutral (N) wires to the load (appliances/circuit) from the "OUT" terminals of the device.
   • Zorg ervoor dat alle verbindingen stevig en veilig zijn.
4. Verificatie: Controleer alle bedradingsaansluitingen nogmaals op juistheid en veiligheid.
5. Stroomherstel: Restore power to the circuit. The device will power on and display the current voltage en huidige metingen.

5. Gebruiksaanwijzing en instellingen

The device displays real-time voltage and current. Use the control buttons to adjust protection parameters.

5.1. Knopfuncties

• Aan/uit-knop: Turns the device ON/OFF (if applicable, or for display cycling).
• Zet knop: Enters/exits setting mode and cycles through parameters.
• Omhoog-pijlknop (▲): Increases parameter values.
• Pijltje omlaag (▼): Decreases parameter values.

5.2. Parameters aanpassen

Om een ​​parameter aan te passen:

1. Druk op de SET Druk op de knop om de instelmodus te openen. De eerste parameter zal knipperen.
2. Pers SET repeatedly to cycle through the available parameters (e.g., Over-voltage protection threshold, Under-voltage protection threshold, Over-current protection threshold, recovery delays, etc.).
3. When the desired parameter is flashing, use the ▲ (Omhoog en ▼ (Down) buttons to adjust its value.
4. After setting the value, wait a few seconds for the device to automatically save the setting and exit the setting mode, or press SET again to move to the next parameter.

5.3. Parameter Ranges and Default Values (for 220V/80A model)

Note: The over-current adjustment range is inferred to be up to 80A for the TOVPD1-80-EC model, although the provided description mentions 40A and 63A variants. Always refer to the specific markings on your device.

5.4. Fabrieksinstellingen herstellen

To restore the device to its factory default settings, press and hold the ▼ (Down) button for more than 12 seconds. The display will indicate a reset.

5.5. Error Inquiry

To inquire about past error events, press and hold the ▲ (Up) button for more than 12 seconds. The device will display error codes or logs if available.

6. Onderhoud

• Regularly inspect the device for any signs of physical damage or loose connections.
• Houd het apparaat schoon en stofvrij. Gebruik een droge, zachte doek om het schoon te maken.
• Gebruik geen schurende reinigingsmiddelen of oplosmiddelen.
• Zorg voor voldoende ventilatie rond het apparaat om oververhitting te voorkomen.

7. Probleemoplossing

8. Specificaties