ErGear Dual Monitor Stand EGCM3-E Instruction Manual

Invoering

This manual provides detailed instructions for the assembly, operation, and maintenance of your ErGear Dual Monitor Stand, model EGCM3-E. Please read this manual thoroughly before installation and retain it for future reference. This monitor stand is designed to support two monitors ranging from 13 to 32 inches, with a maximum weight capacity of 8 kg (17.6 lbs) per arm.

Veiligheidsinformatie

• Controleer vóór de montage of alle onderdelen aanwezig en onbeschadigd zijn. Gebruik het product niet als er onderdelen ontbreken of defect zijn.
• Do not exceed the maximum weight capacity of 8 kg (17.6 lbs) per arm. Overloading may result in instability and potential injury.
• This stand is compatible with VESA mounting patterns of 75x75mm and 100x100mm. Verify your monitor's VESA pattern before installation.
• Always use two people for lifting and mounting monitors to prevent injury.
• Ensure the stand is placed on a stable, level surface.
• Houd kinderen en huisdieren uit de buurt tijdens de montage.

Inhoud van het pakket

Please check to ensure all parts are included in your package:

• Basisplaat
• Steunpaal
• Monitorarmen (2)
• VESA-platen (2)
• Clips voor kabelbeheer
• Montageset (schroeven, ringen, inbussleutels)

Installatie-instructies

Stap 1: Monteer de basis en de paal

Attach the support pole to the base plate using the provided screws. Ensure the connection is secure and stable.

The sturdy base plate provides stability for the dual monitor setup. Dimensions are approximately 41cm by 26cm.

Step 2: Attach Monitor Arms to the Pole

Slide the monitor arms onto the support pole. Adjust them to your desired height and tighten the securing mechanism. Note that both arms adjust vertically together.

Stap 3: Bevestig VESA-platen aan monitoren

Secure the VESA plates to the back of your monitors using the appropriate screws from the hardware kit. Ensure the VESA pattern (75x75mm or 100x100mm) matches.

Each arm is designed to hold monitors up to 8 kg (17.6 lbs) and supports VESA 75x75mm or 100x100mm mounting patterns for 13-32 inch screens.

Step 4: Mount Monitors to Arms

Carefully slide the monitors (with VESA plates attached) onto the monitor arms. Secure them in place with the locking screws or clips provided.

Bediening en afstellingen

The ErGear Dual Monitor Stand offers a range of adjustments for optimal viewcomfort en ergonomische positionering.

Hoogteverstelling

To adjust the height of both monitors, loosen the collar on the support pole, slide the arms to the desired height, and then re-tighten the collar. The maximum height extension is approximately 42cm.

Monitors can be raised up to 42cm from the desk surface to achieve an ergonomic viewhoogte.

Kantelen, draaien en roteren

Each monitor arm allows for flexible positioning:

• Kantelen: Adjust the monitor screen ±45° (up or down) to reduce glare and optimize viewhoeken.
• Draaibaar: Pivot the monitor 180° (left or right) to share your screen or change viewrichting.
• Rotatie: Draai de monitor 360° om te wisselen tussen liggende en staande weergave.

The stand allows for versatile adjustments including tilt, swivel, and full 360-degree rotation for each monitor.

Easily switch monitors between landscape and portrait modes for different tasks.

Kabelbeheer

The stand features integrated cable management clips to keep your workspace tidy and organized. Route your monitor and power cables along the arms and down the support pole using the provided clips.

Utilize the integrated cable management system to maintain a clean and organized desk environment.

Onderhoud

• Controleer regelmatig alle schroeven en verbindingen om er zeker van te zijn dat ze goed vastzitten.
• Maak de standaard schoon met een zachte, damp doek. Vermijd schurende reinigingsmiddelen of oplosmiddelen.
• Do not lubricate any moving parts unless specifically instructed by the manufacturer.

Probleemoplossing

De monitoren staan ​​niet waterpas:

Check if the VESA plates are securely attached to both monitors and the arms. Ensure the arms are at the same height on the pole. Minor adjustments can often be made by slightly loosening and re-tightening the VESA plate screws.

De standaard voelt instabiel aan:

Verify that the base is on a flat, stable surface. Ensure all screws, especially those connecting the pole to the base, are fully tightened. Confirm that the combined weight of your monitors does not exceed the stand's capacity.

Moeilijkheden bij het aanpassen van de kantel-/draaihoek:

Some joints may have tension adjustment screws. Refer to the assembly diagrams for specific locations and use the provided Allen key to loosen or tighten as needed.

Specificaties

Garantie en ondersteuning

For warranty information or technical support, please refer to the documentation included with your purchase or contact ErGear customer service directly. Contact details can typically be found on the manufacturer's official webwebsite of op de productverpakking.