1. Product voorbijview
The Total TWP47506 750W Automatic Jet Water Pump is designed for efficient clean water collection and distribution. It is suitable for drawing water from wells, boreholes, open tanks, and other water supply sources. Primary applications include watering vegetable gardens, personal plots, and ensuring water circulation in fountains and various water features. Its design prioritizes ease of maintenance and portability, featuring an external tank location. The pump incorporates a brushless induction motor for long-lasting, maintenance-free operation. The robust cast iron pump casing can be rotated 90 degrees for flexible installation. This pump is capable of integration into automated water supply systems.
Figuur 1: Total TWP47506 750W Automatic Jet Water Pump. This image shows the complete pump unit with its motor and casing.
2. Veiligheidsinstructies
Read all safety warnings and instructions carefully before operating this product. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.
Algemene veiligheid
- Draag altijd de juiste persoonlijke beschermingsmiddelen (PBM), zoals een veiligheidsbril en handschoenen.
- Zorg ervoor dat de pomp op een stabiele, vlakke ondergrond staat om omvallen te voorkomen.
- Houd kinderen en onbevoegde personen uit de buurt van het werkgebied.
- Do not operate the pump in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Never use the pump to transfer flammable, corrosive, or explosive liquids.
- Disconnect the power supply before performing any maintenance, cleaning, or when the pump is not in use.
Elektrische veiligheid
- Zorg ervoor dat de voeding voltage matches the specifications on the pump's rating label (220-240V, 50Hz).
- Use a properly grounded outlet. Do not modify the plug.
- Do not expose the pump or electrical connections to rain or wet conditions.
- Avoid using extension cords unless absolutely necessary. If an extension cord is used, ensure it is rated for outdoor use and has the correct gauge for the pump's power requirements.
- Never carry the pump by its power cord.
- Controleer het netsnoer regelmatig op beschadigingen. Laat het snoer in geval van schade vervangen door een gekwalificeerde elektricien.
3. Inhoud van het pakket
Controleer bij het uitpakken of alle onderstaande artikelen aanwezig en onbeschadigd zijn:
- 1 x Total TWP47506 750W Automatic Jet Water Pump
- 1 x drukschakelaar
- 1 x Stainless Steel Hose
- 1 x manometer
- 1 x Three-way Brass Fitting
- Gebruikershandleiding (dit document)
4. Technische specificaties
| Specificatie | Waarde |
|---|---|
| Modelnummer | TWP47506 |
| Type | Self-priming Automatic Jet Pump |
| Nominaal vermogen | 750W (1.0 pk) |
| Deeltage | 220-240V |
| Frequentie | 50Hz |
| Max Hoofd | 45 meter |
| Maximale stroom | 60 liter/minuut |
| Max. Afzuiging | 9 meter |
| Buisdiameter | 1 x 1 inch |
| Motortype | Copper Wire Induction Motor (Brushless) |
| Waaiermateriaal | Roestvrij staal |
| Pomp Casing Materiaal | Gietijzer |
| Kabellengte | 0.3 meter |
| Tank Capacity (Cylindrical) | 24 liter |
| Productafmetingen (L x B x H) | 30x19x22cm |
| Artikelgewicht | 1.5 kg |
| Kleur | Zilver |
5. Installatie en installatie
5.1 Plaatsing
- Position the pump on a firm, level, and dry surface.
- Zorg voor voldoende ventilatie rond de pomp om oververhitting te voorkomen.
- Protect the pump from direct exposure to weather elements (rain, direct sunlight, frost).
- Keep the pump as close as possible to the water source to minimize suction lift and maximize efficiency.
5.2 Aansluiten van leidingen
The pump is equipped with standard inch fittings for both suction and discharge pipes.
- Aanzuigleiding: Connect a rigid, airtight suction pipe (1 inch diameter) to the pump's inlet. Ensure all connections are sealed to prevent air leaks, which can affect priming and pump performance. A foot valve with a strainer should be installed at the end of the suction pipe submerged in the water source to prevent debris from entering the pump and to maintain prime.
- Uitlaatpijp: Connect a discharge pipe (1 inch diameter) to the pump's outlet. Use the provided three-way brass fitting, pressure switch, and pressure gauge as part of your water supply system. Ensure all connections are secure.
5.3 De pomp vullen
This is a self-priming pump, but initial priming is crucial for proper operation. Before first use or after the pump has run dry:
- Ensure the suction pipe is fully submerged in the water source.
- Locate the priming plug on the top of the pump casing.
- Unscrew the priming plug and slowly fill the pump casing with clean water until it overflows.
- Replace and securely tighten the priming plug.
- Open any valves on the discharge side to allow air to escape during startup.
5.4 Elektrische aansluiting
- Connect the pump's power cord to a grounded electrical outlet (220-240V, 50Hz).
- Ensure the electrical circuit is protected by a Residual Current Device (RCD) for added safety.
6. Bediening
6.1 Starten van de pomp
- Ensure the pump has been properly primed (Section 5.3).
- Verify all pipe connections are secure and leak-free.
- Plug the pump into the power outlet. The pump will start automatically if connected to an automated system with a pressure switch.
- Observe the pressure gauge. The pressure should rise as the pump builds pressure.
- If the pump does not draw water within a few minutes, switch it off, re-prime, and check for air leaks in the suction line.
6.2 Automatische werking
When integrated into a water supply system with the included pressure switch, the pump will automatically start when water pressure drops (e.g., when a tap is opened) and stop when the desired pressure is reached (e.g., when the tap is closed). The 24-liter cylindrical tank helps maintain consistent pressure and reduces pump cycling.
6.3 De pomp stoppen
For temporary shutdown, close all water outlets. The pump will stop automatically if operating in an automated system. For complete shutdown or extended periods of non-use, unplug the pump from the power supply.
7. Onderhoud
Regular maintenance ensures optimal performance and extends the lifespan of your pump. Always disconnect the power supply before performing any maintenance.
7.1 Regelmatige controles
- Inspecteer het netsnoer en de stekker op tekenen van schade.
- Check all pipe connections for leaks. Tighten if necessary.
- Ensure the foot valve strainer is clear of debris. Clean if clogged.
- Listen for unusual noises during operation, which may indicate a problem.
7.2 Reinigen
Veeg de buitenkant van de pomp af met adamp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the motor's ventilation openings are free from dust and debris.
7.3 Winterklaar maken (voor koude klimaten)
If the pump is exposed to freezing temperatures, it must be drained to prevent damage:
- Koppel de stroomtoevoer los.
- Laat al het water uit de pomp lopenasing by unscrewing the drain plug (if present) or by tilting the pump.
- Disconnect the suction and discharge pipes and drain them completely.
- Bewaar de pomp op een droge, vorstvrije plaats.
8. Probleemoplossing
Voordat u contact opneemt met de klantenservice, raadpleegt u de volgende tabel met veelvoorkomende problemen en oplossingen.
| Probleem | Mogelijke oorzaak | Oplossing |
|---|---|---|
| Pomp start niet | Geen stroomvoorziening Defect netsnoer/stekker Motor overload protection tripped |
Controleer de stroomaansluiting en het stopcontact Inspecteren en vervangen indien beschadigd Allow motor to cool, then restart. Check for blockages. |
| Pomp draait, maar er komt geen water | Pomp niet gevuld Luchtlekkage in aanzuigleiding Zuighoogte te hoog Voetklep verstopt of vastgelopen Waterbron leeg |
Re-prime the pump (Section 5.3) Controleer alle zuigaansluitingen op lekkage en draai ze goed vast. Verplaats de pomp dichter naar de waterbron. Reinig of vervang de voetklep. Ensure adequate water in source |
| Lage stroming of druk | Partial blockage in pipes/impeller Luchtlekkage in aanzuigleiding Versleten waaier Incorrect pressure switch setting |
Inspect and clear blockages Check and seal suction connections Neem contact op met gekwalificeerd servicepersoneel. Adjust pressure switch according to manufacturer guidelines (if adjustable) |
| De pomp schakelt frequent aan en uit. | Leak in discharge system Pressure tank pre-charge incorrect Defecte drukschakelaar |
Check for leaks in pipes, fittings, or fixtures Check and adjust pressure tank air pre-charge Inspect and replace pressure switch if necessary |
9. Garantie en ondersteuning
This Total TWP47506 750W Automatic Jet Water Pump comes with a standard manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including warranty period and coverage details.
For technical assistance, spare parts, or warranty claims, please contact Total customer support through your retailer or visit the official Total website for contact information in your region. When contacting support, please have your model number (TWP47506) and purchase date available.