ES725

ES 725 Battery/Starting/Charging Tester User Manual

Model: 725

1. Inleiding

This manual provides detailed instructions for the safe and effective operation of the ES 725 Battery/Starting/Charging Tester. The ES 725 is designed to test 6 and 12-volt batteries, as well as 12 and 24-volt charging systems. It performs a guided test sequence covering battery condition, cranking volts, and the overall charging system, including alternator voltage and AC ripple for bad diodes.

2. Veiligheidsinformatie

Always observe the following safety precautions when using the ES 725 Tester:

  • Wear appropriate eye protection (safety glasses) and protective clothing.
  • Zorg voor voldoende ventilatie bij het werken met batterijen, aangezien deze explosieve gassen kunnen produceren.
  • Avoid sparks or open flames near batteries.
  • Raak onder spanning staande elektrische onderdelen niet aan.
  • Keep the tester dry and clean. Do not expose it to rain or moisture.
  • Refer to the vehicle manufacturer's service manual for specific safety procedures related to the vehicle's electrical system.

3. Inhoud van het pakket

Controleer of alle artikelen in het pakket aanwezig zijn:

  • ES 725 Battery/Starting/Charging Tester unit
  • Gebruikershandleiding (dit document)
  • Test leads with clamps

4. Producteigenschappen

The ES 725 Tester offers the following key features:

  • Tests battery condition and the starting/charging system.
  • Battery test results include State of Health percentage, State of Charge percentage, and actual CCA capacity.
  • Removes surface charge prior to battery test for accurate results.
  • 2-line LCD display available in 7 languages.
  • CCA test range: 40 - 2000 CCA.
  • Tests 6V and 12V batteries.
  • Tests 12V and 24V charging systems.

5. Instellen

Before operating the ES 725 Tester, ensure it is properly set up:

  1. Energiebron: The unit is battery-powered. Ensure a fresh 9-volt battery is installed in the designated compartment.
  2. Testkabels aansluiten: Bevestig de rode klamp aan de positieve (+) batterijpool en de zwarte clamp to the negative (-) battery terminal. Ensure a secure connection.
  3. Initieel scherm: The LCD will power on and display the initial menu.

6. Gebruiksaanwijzing

The ES 725 provides a guided test sequence. Follow the on-screen prompts.

6.1. Batterijtest

  1. Connect the tester to the battery terminals as described in the Setup section.
  2. Select "Battery Test" from the main menu using the navigation buttons.
  3. Voer de koudstartstroom van de accu in. Amps (CCA) rating when prompted. This information is typically found on the battery label.
  4. The tester will automatically remove surface charge and perform the test.
  5. Results will display State of Health (SOH), State of Charge (SOC), and actual CCA capacity.

6.2. Cranking Volts Test

  1. Ensure the tester is connected to the battery.
  2. Select "Cranking Volts Test" from the menu.
  3. Follow the on-screen instructions to crank the engine for a short period (typically 5-10 seconds). Do not start the engine.
  4. De tester meet het volumetage drop during cranking and display the results, indicating the starter's performance.

6.3. Test van het laadsysteem

  1. With the tester connected, select "Charging System Test."
  2. Start the vehicle's engine and allow it to idle.
  3. The tester will measure the alternator's output voltage and check for AC ripple, which can indicate faulty diodes.
  4. Follow any additional on-screen prompts, such as increasing engine RPM, if requested by the tester.
  5. The results will indicate the health of the charging system.

7. Onderhoud

To ensure the longevity and accuracy of your ES 725 Tester:

  • Schoonmaak: Veeg het apparaat af met een zachte, droge doek. Gebruik geen schuurmiddelen of oplosmiddelen.
  • Opslag: Bewaar de tester op een koele, droge plaats, uit de buurt van direct zonlicht en extreme temperaturen.
  • Batterij vervangen: Replace the internal 9-volt battery when the low battery indicator appears on the display.
  • Lead Inspection: Periodically inspect the test leads and clamps for damage. Replace if any wear or damage is observed.

8. Probleemoplossing

ProbleemMogelijke oorzaakOplossing
Tester gaat niet aan.Een lege of verkeerd geplaatste 9V-batterij.Replace the 9V battery or ensure it is correctly installed.
Onnauwkeurige testresultaten.Poor connection to battery terminals; incorrect CCA input; battery surface charge not removed.Zorg ervoor dat clamps are clean and securely attached. Verify correct CCA input. The tester automatically removes surface charge, but ensure battery has rested for a few minutes if recently charged.
Er verschijnt een foutmelding op het scherm.Batterij voltage too low; connection issue; internal fault.Controleer batterijvolumetage (if extremely low, tester may not function). Re-check connections. If problem persists, contact support.

9. Specificaties

  • Model: 725
  • Batterijvolumetage Compatibiliteit: 6V, 12V
  • Oplaadsysteem Voltage Compatibiliteit: 12V, 24V
  • CCA Test Range: 40 - 2000 CCA
  • Weergave: 2-regelig LCD
  • Energiebron: 9-volt batterij
  • Afmetingen (L x B x H): 27.9 x 25.4 x 7.6 cm (ongeveer)
  • Gewicht: 771 g (ongeveer)

10. Garantie en ondersteuning

Voor garantie-informatie of technische ondersteuning kunt u terecht bij de officiële website van de fabrikant. webwebsite of neem contact op met hun klantenservice. Bewaar uw aankoopbewijs als aankoopbewijs.

Fabrikant: Elektronische specialiteiten

Merk: ES

Model: 725

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.